Your foosball table is protected during is whole transport by a packaging containing various plates and protections. When you open the package, we recommend you to use the chipboard plate that cover your foosball table as a support during the assembly.

Insert the skate screw (Ref. 2215) into one of the foot (Ref. 8620 / 8621) and screw it all the way with the 13" flat wrench. Repeat this operation for the three other foot. Once your foosball table is assembled, if necessary, you can unscrew it to ajust the planarity of your foosball.

Snap the head of the skate screw (Ref. 2215) into the skate (Ref. 4821.0). Repeat this process with the other three feet.

Once the glides (Ref. 2215) are assembled to each foot, clip the non-slip pads (Ref. 4825) to them.

Take one of the right foot (Ref. 8620) and one of the left foot (Ref. 8621), then position the crossbar (Ref. 8622) so that the holes of these three elements are aligned. Screw moderatly one of the foot to the crossbar and the other one. To do this, use the 10" diameter metal screws (Ref. 1741) with the 10" diameter discs (Ref. 1222) on the foot side then position the nut at the base, screw it by hand without forcing. In the first time, Dans un premier temps, don't overtighten the screw. Next, adjust the inclination of the crossbar until it is parallel with the back of the feet.
Now you can screw the screws with the 6" Allen wrench. Repeat this step with the 2 others feet.

Apply of the right clapier, including the Conrilleau's logo in ecope (Ref. 7490.0 / 7490.9) on one the right foot at the level of the crossbar. Adjust the inclination of these such as the crossbar flush with the back of the clapier. Remove the clapier, with the 6" Allen wrench, screw the metal screw (Ref. 1741) that should be behind the clapier and links the crossbar to the foot. Repeat this step for the other right foot.

Apply of the left clapier, without the logo(Ref. 7489.0 / 7489.9) on one the left foot at the level of the crossbar. Adjust the inclination of these such as the crossbar flush with the back of the clapier. Remove the clapier, with the 6" Allen wrench, screw the metal screw (Ref. 1741) that should be behind the clapier and links the crossbar to the foot. Repeat this step for the other left foot..

On the ground, put a foam protection used during the transport of your foosball table. Set it near a wall, approximately at 12" (30cm). Place the foosball table, verticaly, players face to the wall. Make sure to have a sufficient inclination to make the goal cannot touch the wall.
WARNING : The box mustn't be in a direct contact with the ground or the wall.
Use the foam protections sets with the package. Don't hesitate to stacked two of them to have better thickness.

While a person is holding the foosball table and the feet, the second one align the discs (Ref. 1221) and screw the 8" diameter metal screws (Ref. 1740) on the inside of the box, in the way of the binder nuts situates on the outdoor side of the box (Ref. 1089.0). To do this, use the 6" Allen wrench. Repeat this step on each foot.

Now, you can put it right side up your foosball table. For this manipulation, it is important to lift the foosball table to make sure to not take support from the feet until they are not straight.
Don't hesitate to make this operation with several people to make this manipulation easier. It is preferable to be three to realize it without encumbers.

Now you can install the handles to play. To do that, hold strongly one the player and screw the handle. Repeat this operation for the eight handles. Make sure to install the black one at the end of the bar of the black players and the white one on the bar of the white players.